(燕山大學 機械工程學院，秦皇島 066004)
摘 要: 將TA15鈦合金在Gleeble-3800熱模擬試驗機上進行熱壓縮試驗，變形溫度為800~980 ℃。采用掃描電鏡(SEM)分析該合金的微觀組織演變規律，結合微觀組織定量結果及流變曲線對TA15鈦合金熱變形過程中熱力學進行評價。結果表明：TA15鈦合金在兩相區熱變形時會發生動態相變。動態相變使真實應力-應變曲線呈現明顯的流變軟化現象，造成屈服應力顯著高于穩態應力。初生α相含量對變形溫度及應變敏感。隨著變形溫度溫度的升高或應變的增加，初生α相含量降低甚至完全消失，表明動態相變會造成TA15鈦合金相變點降低。TA15鈦合金動態相變是一種應力驅動型相變，該合金發生動態相變的條件是驅動力克服能量勢壘。能量勢壘數值上等于最小臨界驅動力，且范圍約為70~742 J/mol，而最大驅動力范圍約為507~3306 J/mol。最大/最小臨界驅動力、能量勢壘均隨著變形溫度的升高而降低。
關鍵字: TA15鈦合金；流變軟化；動態相變；應力驅動型；熱力學評價
（School of Mechanical Engineering, Yanshan University, Qinhuangdao 066004, China）
Abstract:The hot compression tests of TA15 titanium alloy were carried out on Gleeble-3800 thermomechanical simulator with a deformation temperature range of 800-980 ℃. The microstructure evolution of TA15 titanium alloy was analyzed by scanning electron microscopy (SEM). Combined with the quantitative data of microstructure and flow curve, the thermodynamics evaluation of TA15 titanium alloy during hot deformation was explained. The results show that dynamic transformation (DT) can be observed in TA15 titanium alloy during hot deformation below the β-transus temperature (Tβ), which can cause the true stress-strain curves to show apparently flow softening phenomenon leading to the yield stress significantly higher than the steady stress. The volume fraction of the primary α phase (fαp) is sensitive to deformation temperature and strain. With the increase of deformation temperature or strain, the fαp decreases or even disappears completely, indicating that the DT can cause the Tβ of TA15 titanium alloy to decline. The DT in TA15 titanium alloy is a stress-induced type, and its activation condition is that the driving force overcomes the energy barrier. The energy barrier value is numerically equal to the minimum critical driving force with 70-742 J/mol, and the range of the maximum driving force is 507-3306 J/mol. The maximum and minimum driving force and energy barrier decrease with the increase of deformation temperature.
Key words: TA15 titanium alloy; flow softening; dynamic transformation; stress-induced type; thermodynamics evaluation
