(1. 金華職業技術學院 機電工程學院，金華 321007；
2. 南京工業職業技術學院 工程技術實訓中心，南京 210023；
3. 金華職業技術學院 汪衛華院士專家工作站，金華 321007；
4. 江蘇省精密制造工程技術研究開發中心，南京 210023)
摘 要: 借助電子背散射衍射(EBSD)和透射電子顯微鏡(TEM)研究6082鋁合金在623~773 K和0.01~5 s-1條件等溫?zé)釅嚎s時的動態再結晶行為。結果表明：6082鋁合金真應力-應變曲線雖無明顯單峰值特征，但仍發生動態再結晶，并且動態再結晶程度與Z參數緊密相關。在ln Z=24.9014(723 K, 0.1 s-1)熱壓縮時，動態再結晶體積分?jǐn)?shù)最高，為38.6%。應用加工硬化率確定了動態再結晶初始臨界應變，建立臨界應變與Z參數之間的定量關系，得到動態再結晶臨界應變方程。結合EBSD分析測試結果建立6082鋁合金動態再結晶動力學模型。微觀組織分析發現，原始晶粒內形成的亞晶結構隨著變形的進行持續吸收位錯，其取向差不斷增大至大角度晶界，從而形成新的再結晶晶粒。在原始晶界附近通過亞晶界遷移引起亞晶粗化，使其小角度晶界形成大角度晶界的連續動態再結晶是其動態再結晶的主要機制。
關鍵字: 6082鋁合金；動態再結晶模型；Zener-Hollomon參數；連續動態再結晶
（1. Mechanical & Electrical Engineering College, Jinhua Polytechnic, Jinhua 321007, China;
2. Engineering Technology Training Center, Nanjing Institute of Industry Technology, Nanjing 210023, China;
3. Academician Wang Weihua Expert Workstation, Jinhua Polytechnic, Jinhua 321007, China;
4. Jiangsu Research and Development Center of Precision Manufacturing, Nanjing 210023, China）
Abstract:The dynamic recrystallization behaviors of 6082 aluminum alloy at the temperature range of 623-773 K and strain rate range of 0.01-5 s-1 were studied by electron back scattered diffraction (EBSD) and transmission electron microscopy (TEM). According to the experimental results, dynamic recrystallization occurs during hot deformation of 6082 aluminum alloy, although the true stress-strain curve has no obvious single peak characteristic, and the degree of dynamic recrystallization is closely related to Z parameter. Hot compression with ln Z=24.9014 (723 K, 0.1 s-1) gives rise to the highest fraction of recrystallization of 38.6%. The initial critical strain of dynamic recrystallization was determined by work hardening rate. The quantitative relationship between critical strain and Z parameters was established. Based on the results of EBSD analysis and measurement, a dynamic recrystallization kinetics model of 6082 aluminum alloy during hot deformation is deduced. Microstructure analysis shows that the subgrain structure formed in the original grain is coarsened by grain boundary migration, and the orientation difference increases continuously until the large angle grain boundary is formed, resulting in dynamic recrystallization grains, and the likely mechanism is continuous dynamic recrystallization.
Key words: 6082 aluminum alloy; dynamic recrystallization model; Zener-Hollomon parameter; continuous dynamic recrystallization
