(1. 華南理工大學 機械與汽車工程學院，廣州 510640；
2. 華南理工大學 國家金屬材料近凈成形工程技術研究中心，廣州 510640)
摘 要: 采用劇塑性變形工藝(等通道轉角擠壓和軋制)以及隨后的短時間退火制備高性能Mg-Li合金，通過顯微組織觀察、掃描電鏡分析、X射線衍射儀測試和室溫拉伸測試等研究變形前后合金組織、力學性能及強化機制。結果表明：合金鑄態晶粒粗大，主相為β相，α相分布于β相的晶界以及晶內；同時，晶內存在大量Al2Y和AlLi析出相。由于動態回復作用顯著，合金變形時并未發生明顯的動態再結晶現象；經短時間退火后，合金組織發生完全再結晶，其晶粒細化至27.1 μm(12pra工藝，即等通道轉角擠壓、軋制及退火)。鑄態合金的抗拉強度和伸長率分別為131.1 MPa和47.1%；經12pr(等通道轉角擠壓及軋制)變形后，合金的伸長率達到90.5%，而抗拉強度稍有提高，這主要受位錯協調變形及動態回復作用的影響；退火后合金的伸長率顯著降低而強度提高至237.6 MPa (12pra)，出現退火致強化現象，其主要的機制是有限位錯源強化及晶界強化。
關鍵字: Mg-Li合金；等通道轉角擠壓；軋制；退火；顯微組織；力學性能
（1. School of Mechanical and Automotive Engineering, South China University of Technology,
Guangzhou 510640, China;
2. National Engineering Research Center of Near-Net-Shape Forming for Metallic Materials,
South China University of Technology, Guangzhou 510640, China）
Abstract:The microstructure, mechanical properties and strengthening mechanism of Mg-Li alloys processed by severe plastic deformation (equal channel angular pressing (ECAP) and rolling) and subsequent annealing were analyzed by OM, SEM, XRD and tensile testing. The results show that the initial grains of the as-cast alloy are coarse and β phase occupies the main position, while α phase distributes inside or in the boundary. Meanwhile, there are lots of precipitate phases Al2Y and AlLi in the grain. Obvious dynamic recrystallization (DRX) does not occur during the deformation due to the significant effect of dynamic recovery (DR). After a short time annealing, the alloy is completely recrystallized with grain size refined to 27.1 μm (process of 12pra: ECAP, rolling and annealing). The tensile strength and elongation of the as-cast alloy are 131.1 MPa and 47.1%, respectively. After the process of 12pr (ECAP and rolling), the elongation of the alloy reaches 90.5%, while the tensile strength is improved slightly. This can be explained based on the effect of DR and dislocation-coordinated deformation. Subsequent annealing treatment results in an increase in tensile strength (12pra: 237.6 MPa) and a significant decrease in elongation because of the dislocation source-limited hardening and grain boundary strengthening mechanism.
Key words: Mg-Li alloy; equal channel angular pressing; rolling; annealing; microstructure; mechanical property
