(哈爾濱工業大學 現代焊接生產技術國家重點實驗室，哈爾濱 150001)
摘 要: 利用Al-Si-Mg釬料和自制工藝罩內置Mg粉方法，實現化學鍍鎳Al2O3陶瓷與5A05鋁合金的真空釬焊連接，并分析保溫時間及連接溫度對接頭界面結構和抗剪強度的影響。結果表明：連接溫度570 ℃，保溫時間15 min為最佳工藝參數，此時接頭界面結構為Al2O3/Ni(Ⅰ區)/Al3Ni2(Ⅱ區)/Al3Ni+Mg2Si(Ⅲ區)/α(Al)+Mg2Si(Ⅳ區)/5A05，接頭的抗剪強度為25 MPa。隨著保溫時間的延長，Ni層變薄，Al3Ni2組織的變化不大，Al3Ni+Mg2Si組織逐漸變寬，且呈分散趨勢；當保溫時間延長到50 min時，Al3Ni+Mg2Si完全變成零亂的形狀、大小不一的塊狀分布，且靠近5A05側的Mg2Si消失。連接溫度對界面組織結構的影響與保溫時間的影響相似，接頭斷裂形式為脆性斷裂。當接頭的強度較低時，斷裂發生在鋁合金側的α(Al)+Mg2Si附近；當接頭的強度較高時，斷裂發生在鍍Ni層+界面區(Ⅱ區與Ⅲ區)。
關鍵字: Al2O3陶瓷；化學鍍鎳；真空釬焊；界面結構；抗剪強度
（State Key Laboratory of Advanced Welding Production Technology, Harbin Institute of Technology,
Harbin 150001, China）
Abstract:Vacuum brazing of Al alloy and electroless nickel plated alumina was carried out with Al-Si-Mg brazing alloy and Mg powder in home-made technical hood. Effects of brazing temperature and holding time on the interface structure and shear strength of joints were analyzed. The experimental results show that the interface structure is Al2O3/Ni(Ⅰzone)/Al3Ni2 (Ⅱzone)/Al3Ni+Mg2Si(Ⅲ zone)/α(Al)+Mg2Si(Ⅳ zone)/5A05 when the brazing temperature is 570 ℃ and holding time is 15 min. The maximum shear strength of joints is up to 25 MPa. As the holding time prolongs, Ni layer becomes thin, Al3Ni zone changes little and Al3Ni+Mg2Si zone becomes thick and dispersed. When the holding time is 50 min, Al3Ni+Mg2Si zone becomes scattered and Mg2Si near 5A05 alloy disappears. The effect of brazing temperature on the joints is similar to that of holding time. The fracture mode of joints is brittle. When the shear strength of joints is lower, the joints fracture near α(Al)+Mg2Si on Al alloy side. When the shear strength of joints is higher, the joints fracture on Ni+interface (Ⅱzone and Ⅲ zone).
Key words: Al2O3 ceramic; electroless nickel plating; vacuum brazing; interface structure; shear strength
